Mitsubishi MOTION CONTROLLERS Q173DCPU Manuale delle Istruzioni Pagina 9
- Pagina / 252
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
A - 8
(6) Usage methods
CAUTION
Immediately turn OFF the power if smoke, abnormal sounds or odors are emitted from the
Motion controller, servo amplifier or servomotor.
Always execute a test operation before starting actual operations after the program or
parameters have been changed or after maintenance and inspection.
Do not attempt to disassemble and repair the units excluding a qualified technician whom our
company recognized.
Do not make any modifications to the unit.
Keep the effect or electromagnetic obstacles to a minimum by installing a noise filter or by using
wire shields, etc. Electromagnetic obstacles may affect the electronic devices used near the
Motion controller or servo amplifier.
When using the CE Mark-compliant equipment, refer to the User's manual for the Motion
controllers and refer to the corresponding EMC guideline information for the servo amplifiers,
inverters and other equipment.
Use the units with the following conditions.
Item Conditions
Input power According to each instruction manual.
Input frequency According to each instruction manual.
Tolerable momentary power failure According to each instruction manual.
(7) Corrective actions for errors
CAUTION
If an error occurs in the self diagnosis of the Motion controller or servo amplifier, confirm the
check details according to the instruction manual, and restore the operation.
If a dangerous state is predicted in case of a power failure or product failure, use a servomotor
with electromagnetic brakes or install a brake mechanism externally.
Use a double circuit construction so that the electromagnetic brake operation circuit can be
operated by emergency stop signals set externally.
24VDC
B
RA1
EMG
Servo motor
Electromagnetic
brakes
Shut off with the
emergency stop
signal (EMG).
Shut off with servo ON signal OFF,
alarm, electromagnetic brake signal.
If an error occurs, remove the cause, secure the safety and then resume operation after alarm
release.
The unit may suddenly resume operation after a power failure is restored, so do not go near the
machine. (Design the machine so that personal safety can be ensured even if the machine
restarts suddenly.)
- SAFETY PRECAUTIONS 2
- For Safe Operations 3
- 2. For fire prevention 3
- 3. For injury prevention 4
- 4. Various precautions 4
- (4) Wiring 8
- (6) Usage methods 9
- (10) General cautions 11
- 1. OVERVIEW 20
- 1 OVERVIEW 21
- 2. SYSTEM CONFIGURATION 30
- Q172D(S)CPU 32
- 2.2.1 Checking serial number 41
- Q173DCPU-S1 42
- 80M1 IND. CONT. EQ 43
- <Screen: GX Works2> 44
- (Note-6) 48
- (Note-7) 48
- (Note-8) 49
- , non-condensing 53
- BottomSide face 54
- With battery cover open 54
- (2) 7-segment LED display 57
- (9) Internal I/F connector 68
- 2.5.2 Power supply module 74
- Q62P POWER 78
- 100-240VAC 78
- Q171ENC-W8 81
- 812345670 84
- I/O Allocations 84
- (b) Input 86
- (a) Servo external signals 87
- (FUJITSU COMPONENT LIMITED) 88
- Applicable connector 94
- 10120-3000PE connector 94
- 10320-52F0-008 connector case 94
- (3M make) 94
- :Twisted pair cable 96
- (a) Specifications 97
- Battery Specifications 97
- (b) Battery replacement 98
- (c) Battery life 98
- 2 SYSTEM CONFIGURATION 100
- (1) Q173DPX name of parts 100
- (Note-1) 101
- (a) Module specifications 102
- • Tracking enable signal 103
- (1) Q173DSXY name of parts 108
- (b) Input/output 110
- 1B1 1A1 2B1 2A1 111
- 1B20 1A20 2B20 2A20 111
- (Note-2) 112
- (Note-2) 118
- 2.5.9 SSCNET cables 120
- CPU module 124
- 2.5.10 Battery 125
- (1) Battery specifications 125
- (Note-3) 126
- (Note-4) 126
- (Note-5) 126
- MITSUBISHI 128
- LITHIUM BATTERY 128
- 3. DESIGN 130
- 3 DESIGN 131
- 3.2 External Circuit Design 133
- FOR AC/DC 135
- MC1 NO M10 136
- (2) Grounding 137
- 3.2.2 Safety circuit design 138
- (2) Emergency stop circuit 138
- (3) Forced stop circuit 138
- 3.3.1 Mounting environment 140
- (Q173DCPU use) 143
- 3.4 Design Checklist 144
- 4. INSTALLATION AND WIRING 146
- 4 INSTALLATION AND WIRING 147
- (1) Fitting dimensions 149
- (Correct) (Wrong) 155
- Motion CPU module 156
- (a) Minimum bend radius 157
- (b) Tension 157
- (c) Lateral pressure 157
- (d) Twisting 158
- (e) Disposal 158
- 4.2.2 Battery cable 162
- Base unit Q173DSCPU/Q172DSCPU 165
- 4.3 Mounting of Battery 166
- 4.5 Wiring 169
- (1) Power supply wiring 169
- (3) Grounding 171
- 5. START-UP PROCEDURES 174
- 5 START-UP PROCEDURES 175
- 6.1 Maintenance Works 185
- Electromagnetic 186
- 6.2 Daily Inspection 187
- Table 6.1 Daily Inspection 187
- 6.3 Periodic Inspection 188
- 6.4 Life 189
- Table 6.3 Life 189
- (1) Capacitor 189
- (2) Bearing 189
- 6.5 Battery 190
- 6.5.1 Battery life 191
- 7-segment LED 202
- Motion CPU 210
- DC input 210
- 7. EMC DIRECTIVES 212
- 7 EMC DIRECTIVES 213
- (1) Installation 214
- (3) Cables 215
- (1) Ferrite core 217
- (3) Cable clamp 218
- APPENDICES 222
- Insulation sheath 225
- Conductor 225
- (2) Q170ENCCBL M 226
- (a) Model explanation 226
- (b) Connection diagram 226
- Synchronous encoder cable 227
- Type : Q170DBATCBL M 228
- Type : Q170DEMICBL M 229
- (a) Connection diagram 230
- Type: Q173DSXYCBL M 233
- System & Service 234
- (1) Q172DSCPU 235
- (2) Q173DSCPU 235
- (3) Q172DCPU 236
- (4) Q173DCPU 236
- (5) Q172DCPU-S1 237
- (6) Q173DCPU-S1 237
- (2) Q64P 240
- 55.2(2.17)115(4.53) 241
- 98(3.86) 241
- Q64PN POWER 241
- Q170DBATC 242
- (1) Q171ENC-W8 249
- (2) Q170ENC 249
- WARRANTY 250
- IB(NA)-0300133-J 251
Prodotti e manuali riguardandi Sistemi di controllo di accesso Mitsubishi MOTION CONTROLLERS Q173DCPU
Sistemi di controllo di accesso Mitsubishi MOTION CONTROLLERS Q172DCPU Manuale delle Istruzioni
(316 pagine)
(316 pagine)
Sistemi di controllo di accesso Mitsubishi MOTION CONTROLLERS Q172DCPU Manuale delle Istruzioni
(174 pagine)
(174 pagine)
(90 pagine)Baxi Water heaters & boilers user manuals
Starting on 0-9
Commenti su questo manuale